
Honda Civic Type R FK8 / FL5 - Larger Rotor Performance 2 Piece Rotors - (Rear) 340/350x11mm
Stock Level: Good

Est. Delivery: Thursday, February 13 - Monday, February 17
Stock Level: Good
Est. Delivery: Thursday, February 13 - Monday, February 17
Upgrade your Honda Civic Type R FK8/FL5 with our Performance OE Replacement Rotors. With a larger 340/350x11mm size, you'll experience improved braking power and control. Take on the road with confidence and conquer any challenge. Upgrade now and unleash your Honda's full potential!
Made of CM-250 special formulated high carbon alloy cast iron, it allows for an optimal bite, thermal characteristics, high-temperature strength and durability. Rotor rings are heat treated to release stress in the rotor to avoid deformation and vibration then turned by state-of-the-art CBN surface machining to ensure better break-in with new brake pads.
Vibration is reduced as the rotor lateral run-out is kept within 0.03mm and well-balanced: variations are kept within 2 grams. All rotors went through rigorous quality control procedures and inspections to ensure the rotors are fit for their purposes. A slotted rotor improves braking consistency by maintaining a clean contact surface and dissipate heat generated and gases released when the pads come into contact with the rotors. Slotted rotors have a superior advantage over blank rotors in wet or raining conditions by preventing water films to form between the brake pad and rotor surface. Weighing less than most O.E. rotors while maintaining proper thermal capacity, our 2-piece rotors improves overall handling by saving unsprung mass.
Aluminum hats are CNC machined from lightweight 6061-T6 aerospace grade aluminum for high strength and durability under extreme track conditions, then black hard coat/hard anodized to increase resistance to wear and corrosion. Mil-spec Type III anodized hats will not discolor under extreme heat, and are harder and more wear/scratch resistant. Unnecessary materials are taken out from the aluminum hats for maximum weight savings while maintaining proper structural integrity.
*Black hard coat and hard coat anodized hats are the same in terms of performance and durability.
Instead of using adaptors, heavy duty caliper carriers (caliper brackets) are utilized to accommodate the increased disc diameter. The supplied extended caliper carriers share the same design as the OEM ones, and will offer improved structural integrity over adaptors. This ensures the setup to be strong enough for heavy use.
Direct bolt-on without any modifications and designed to work flawlessly with OEM ABS and brake system. Compatible with OEM or aftermarket brake pads with the same pad depth (D)
2-piece design
Minimize chances of brake fade & judder during extended sessions
350x11mm rotor assembly weighs 10.3 lbs (4.65 kg) - save 1.5 lbs of unsprung weight per rotor vs. OEM
Wheel Fitment
This larger rear rotor kit was designed to fit under certain 18 inch wheels. However, not all 18" wheels are compatible due to variations in wheel design. If your wheels are not listed below, please verify fitment using the fitment template.
Wheel Fitment Template Download (PDF): 340x11mm / 350x11mm
> How to use the wheel fitment template (PDF)
350x11mm rotors test fit approved wheels:
- OEM FK8 20x8.5 +60
- Volk Racing TE37 Saga 18x10 +40
- Volk Racing TE37 18x10 +41
- Titan 7 T-S5 18x9.5 +45
- Rays Gram Lights 57DR 18x9.5 +38
- Konig Ampliform 18x9.5 +35
- Superspeed RF05RR 18x9.5 +38
- Enkei TS-5 18x9.5 +45
340x11mm rotors test fit approved wheels:
- Spoon SW388 18x9.5 +40
- Desmond Regamaster EVO II 18x9.5 +45
- Volk Racing CE28SL 18x9.5 +44
Direct replacement of: OEM Honda part # 42510-TGH-A00
Includes:
One pair of Paragon Performance 340/350mm x 11mm 2-piece rotor assemblies with black hard coat/hard anodized 6061-T6 aerospace grade aluminum hats (assembled and ready to install)
One pair of paint matched steel caliper carriers
Detailed installation manual
Application:
Part # (w/ black hard anodized hat): P2R.021.340.110.23200.01.01.01.R / P2R.021.350.110.24200.01.01.01.R
Part # (w/ hard anodized hat): P2R.021.340.110.23200.01.01.02.R / P2R.021.350.110.24200.01.01.02.R
Extra/replacement hardware is available for purchase. We recommend using new hardware when replacing rotors to ensure the rotor ring is attached to the aluminum hat properly. Please refer to our Rotor Assembly Instructions for torque specs and detailed instructions.
Interested in other CTR FK8 (K20C) parts? Click HERE
Specifications:
Diameter: 340/350mm (13.39"/13.78")
Thickness (new): 11mm (0.43")
Thickness (min.): 9mm (0.35")
Type: 2-piece non-floating
Face Pattern: Slotted
Vented / Solid: Solid
Number of Vanes: N/A
Hat Material: 6061-T6 aluminum
Friction Ring Material: CM-250 high carbon alloy cast iron
Rotor Finish: CBN turned
350x11mm rotor assembly weights (per rotor): 10.3 lbs (4.65 kg)
Diameter:
Caliper type: