Skip to content
FREE SHIPPING on all Brake Kits to the continental US
FREE SHIPPING on all Brake Kits to the continental US

Honda Civic Type R FD2 - Larger Rotor Performance 2 Piece Rotors - (Rear) 324mm x 9mm (12.76" x 0.35")

SKU P2R.019.324.090.22200.01.03.01.R
Original price $750.00 USD - Original price $750.00 USD
Original price
$750.00 USD
$750.00 USD - $750.00 USD
Current price $750.00 USD
Brake Hat Finish: Black Anodized
Ask a question

Paragon 2-piece Rotors (Rear Pair) for Honda Civic Type R FD2 - Larger Rotor

Take your Honda Civic Type R FD2 to new heights with our Performance OE Replacement Rotors. These rear pair rotors measure 324mm x 9mm, offering a larger size for enhanced braking power. Make daring moves with confidence, thanks to our reliable and durable Honda rotors. Upgrade your ride today!

Made of CM-250 special formulated high carbon alloy cast iron, it allows for an optimal bite, thermal characteristics, high-temperature strength and durability. Rotor rings are heat treated to release stress in the rotor to avoid deformation and vibration then turned by state-of-the-art CBN surface machining to ensure better break-in with new brake pads.

Vibration is reduced as the rotor lateral run-out is kept within 0.03mm and well-balanced: variations are kept within 2 grams. All rotors went through rigorous quality control procedures and inspections to ensure the rotors are fit for their purposes. A slotted rotor improves braking consistency by maintaining a clean contact surface and dissipate heat generated and gases released when the pads come into contact with the rotors. Slotted rotors have a superior advantage over blank rotors in wet or raining conditions by preventing water films to form between the brake pad and rotor surface. Weighing less than most O.E. rotors while maintaining proper thermal capacity, our 2-piece rotors improves overall handling by saving unsprung mass.

Aluminum hats are CNC machined from lightweight 6061-T6 aerospace grade aluminum for high strength and durability under extreme track conditions, then black hard coat/hard anodized to increase resistance to wear and corrosion. Mil-spec Type III anodized hats will not discolor under extreme heat, and are harder and more wear/scratch resistant. Unnecessary materials are taken out from the aluminum hats for maximum weight savings while maintaining proper structural integrity.
*Black hard coat and hard coat anodized hats are the same in terms of performance and durability.

  • Direct bolt-on without any modifications and designed to work flawlessly with OEM ABS and brake system. Compatible with OEM or aftermarket brake pads with the same pad depth (D)

  • Increases rear rotor diameter by 42mm / 1.65" (14.9%)
  • Further increases brake torque over O.E. sized 2-piece rotors due to improved leverage
  • 2-piece design

  • Minimize chances of brake fade & judder during extended sessions

  • Adapters to accommodate larger rotor size (324mm vs. stock size 282mm)
  • Rotor to hat mounting system: Fixed hat, non-floating (8 bolt)

 

Wheel Fitment

This larger rear rotor kit was designed to fit under certain 17 inch wheels. However, not all 17" wheels are compatible due to variations in wheel design.

Test fit approved wheels:

  • OEM Integra DC5 Type R 17x7 +60

 

Direct replacement of: OEM Honda part # 42510TA0A00 / 42510-TA0-A00 / 42510TA0A01 / 42510TA0A02

 

Includes:

  • One pair of Paragon Performance 324mm x 9mm (12.76" x 0.35") 2-piece rotor assemblies with black hard coat/hard anodized 6061-T6 aerospace grade aluminum hats (assembled and ready to install)

  • One pair of anodized billet aluminum adapters

  • Detailed installation manual

Part # (w/ black hard anodized hat): P2R.019.324.090.22200.01.03.01.R

Part # (w/ hard anodized hat): P2R.019.324.090.22200.01.03.02.R

Extra/replacement hardware is available for purchase. We recommend using new hardware when replacing rotors to ensure the rotor ring is attached to the aluminum hat properly. Please refer to our Rotor Assembly Instructions for torque specs and detailed instructions.

 

 


Specifications:

Diameter: 324mm (12.76")

Thickness (new): 9mm (0.35")

Thickness (min.): 7mm (0.28")

Type: 2-piece non-floating

Face Pattern: Slotted

Vented / Solid: Solid

Number of Vanes: N/A

Hat Material: 6061-T6 aluminum

Friction Ring Material: CM-250 high carbon alloy cast iron

Rotor Finish: CBN turned

Diameter:

Caliper type:

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
Free Shipping

Free on all brake kits to the continental USA

Official Alcon Distributor

Expert Advice, Products, Support

Text or Call

+1 (630) 360-2548

Chat With Us

Click "Assistance" below during business hours.