Paragon 2-piece Rotors (Front Pair) for Jeep Grand Cherokee Trackhawk / Dodge Durango SRT Hellcat

Experience superior braking and cooling efficiency for your Jeep Trackhawk or Durango SRT Hellcat with Paragon Performance 2-piece Rotors, specifically designed for track and race use. These rotors feature directional ventilation vanes that generate suction and turbulence to guide cool air through, resulting in improved heat dissipation and increased durability under intense track conditions.

Made of CM-250 special formulated high carbon alloy cast iron, it allows for an optimal bite, thermal characteristics, high-temperature strength and durability. Rotor rings are heat treated to release stress in the rotor to avoid deformation and vibration then turned by state-of-the-art CBN surface machining to ensure better break-in with new brake pads.

Vibration is reduced as the rotor lateral run-out is kept within 0.03mm and well-balanced: variations are kept within 2 grams. All rotors went through rigorous quality control procedures and inspections to ensure the rotors are fit for their purposes. The fully-floating 2-piece design allows thermal expansion of the rotor while minimizing deformation and ensuring the rotor is self-centered with the pads. A slotted rotor improves braking consistency by maintaining a clean contact surface and dissipate heat generated and gases released when the pads come into contact with the rotors. Slotted rotors have a superior advantage over blank rotors in wet or raining conditions by preventing water films to form between the brake pad and rotor surface. Weighing less than most O.E. rotors while maintaining proper thermal capacity, our 2-piece rotors improves overall handling by saving unsprung mass.

Aluminum hats are CNC machined from lightweight 6061-T6 aerospace grade aluminum for high strength and durability under extreme track conditions, then black hard coat/hard anodized to increase resistance to wear and corrosion. Mil-spec Type III anodized hats will not discolor under extreme heat, and are harder and more wear/scratch resistant. Unnecessary materials are taken out from the aluminum hats for maximum weight savings while maintaining proper structural integrity.

*Black hard coat and hard coat anodized hats are the same in terms of performance and durability.

Due to heavy vehicle weight and absence of effective brake cooling system, premature cracking on the stock rotors are common after track/heavy use. Paragon Performance rotors can be an effective solution to this issue while improving pedal feel and brake modulation.

• Direct bolt-on without any modifications and designed to work flawlessly with OEM ABS and brake system while maintaining factory brake bias. Compatible with OEM brake pads or aftermarket pads with the same pad depth (D)

• Directional ventilation vanes for optimal cooling performance, runs up to 30% cooler than O.E. rotors and increase cooling efficiency by up to 30%

• Fully-floating 2-piece design

• Minimizing brake fade & judder during extended sessions

• Rotor to hat mounting system: H-Bobbin (12 bolt)

• Weighs 32.6 lbs (14.79 kg) per rotor. Save 6.1 lbs / 2.8 kg of unsprung weight per rotor vs. OEM

• Great upgrade from non-directional, pillar vane OEM rotors

Includes:

• One pair of Paragon Performance 400mm x 36mm (15.75” x 1.42”) 2-piece rotor assemblies with black hard coat/hard anodized 6061-T6 aerospace grade aluminum hats, stainless steel bobbins, and anti-rattle clips (assembled and ready to install)

• Detailed installation manual

Replacement rotor rings are available for purchase at a reasonable cost. If you wish to retain the OEM hat, our replacement rotor rings will also fit (direct bolt-on installation).

Direct replacement of: OEM Jeep part # 68305562AB

Applications:

• 2018-2021 Jeep Grand Cherokee Trackhawk

• 2021 Dodge Durango SRT Hellcat

Part # (w/ black hard anodized hat): P2R.208.400.360.21685.06.01.01.F

Part # (w/ hard anodized hat): P2R.208.400.360.21685.06.01.02.F

Extra/replacement hardware is available for purchase. We recommend using new hardware when replacing rotors to ensure the rotor ring is attached to the aluminum hat properly. Please refer to our Rotor Assembly Instructions for torque specs and detailed instructions.

Specifications:

Diameter: 400mm (15.75")

Thickness (new): 36mm (1.42")

Thickness (min.): 34mm (1.34")

Type: 2-piece floating

Face Pattern: Slotted

Vented / Solid: Directional ventilated

Number of Vanes: 48

Hat Material: 6061-T6 aluminum

Friction Ring Material: CM-250 high carbon alloy cast iron

Rotor Finish: CBN turned

Weight (per rotor): 32.6 lbs (14.79 kg)

Cross Reference:

OEM Jeep part # 68305562AB

Diameter:

Caliper type: