Paragon 2-piece Brake Rotors (Rear Pair) for Tesla Model S/X
NOTE: This rotor is for cars equipped with Brembo calipers If you Mondo calipers you should order this rotor instead.
Introducing the Performance OE Replacement Rotors for Tesla Model S and Model X! Upgrade your vehicle's braking power with this pair of 365mm x 28mm rotors. Experience the thrill of confident and responsive braking on the road. Take your driving to the next level with these high-quality replacement rotors.
Made of CM-250 special formulated high carbon alloy cast iron, it allows for an optimal bite, thermal characteristics, high-temperature strength and durability. Rotor rings are heat treated to release stress in the rotor to avoid deformation and vibration then turned by state-of-the-art CBN surface machining to ensure better break-in with new brake pads.
Vibration is reduced as the rotor lateral run-out is kept within 0.03mm and well-balanced: variations are kept within 2 grams. All rotors went through rigorous quality control procedures and inspections to ensure the rotors are fit for their purposes. The floating 2-piece design allows thermal expansion of the rotor while minimizing deformation and ensuring the rotor is self-centered with the pads. A slotted rotor improves braking consistency by maintaining a clean contact surface and dissipate heat generated and gases released when the pads come into contact with the rotors. Slotted rotors have a superior advantage over blank rotors in wet or raining conditions by preventing water films to form between the brake pad and rotor surface. Weighing less than most O.E. rotors while maintaining proper thermal capacity, our 2-piece rotors improves overall handling by saving unsprung mass.
Aluminum hats are CNC machined from lightweight 6061-T6 aerospace grade aluminum for high strength and durability under extreme track conditions, then black hard coat/hard anodized to increase resistance to wear and corrosion. Mil-spec Type III anodized hats will not discolor under extreme heat, and are harder and more wear/scratch resistant. Unnecessary materials are taken out from the aluminum hats for maximum weight savings while maintaining proper structural integrity.
*Black hard coat and hard coat anodized hats are the same in terms of performance and durability.
-
Direct bolt-on without any modifications and designed to work flawlessly with OEM ABS and brake system while maintaining factory brake bias. Compatible with OEM brake pads or aftermarket pads with the same pad depth (D)
-
Directional ventilation vanes for optimal cooling performance, runs up to 30% cooler than O.E. rotors and increase cooling efficiency by up to 30%
-
Floating 2-piece design
-
Minimizing brake fade & judder during extended sessions
- Weighs 18.2 lbs, save 9.6 lbs of unsprung weight vs. OEM (per rotor)
- Rotor to hat mounting system: D-Bobbin (10 bolt)
Direct replacement of: OEM Tesla part # 1027632-00-B
Applications:
- 2012-2020 Tesla Model S Rear (60, 70, 70D AWD, 75D AWD, 85, 85D AWD, P85, P85D AWD, 90D AWD, P90D AWD, 100D AWD, P100D AWD)
- 2015-2020 Tesla Model X Rear (75D AWD, 90D AWD, P90D AWD, 100D AWD, P100D AWD)
***Only fits vehicles with Brembo calipers (separate parking brake calipers). Does not fit vehicles with Mando single piston sliding rear calipers (integrated parking brake function).
Includes:
-
One pair of Paragon Performance 365mm x 28mm (14.37” x 1.10") 2-piece rotor assemblies with black hard coat/hard anodized 6061-T6 aerospace grade aluminum hats, stainless steel bobbins, and anti-rattle clips (assembled and ready to install)
-
Detailed installation manual
Part # (w/ black hard anodized hat): P2R.061.365.280.23700.08.01.01.R
Part # (w/ hard anodized hat): P2R.061.365.280.23700.08.01.02.R
Extra/replacement hardware is available for purchase. We recommend using new hardware when replacing rotors to ensure the rotor ring is attached to the aluminum hat properly. Please refer to our Rotor Assembly Instructions for torque specs and detailed instructions.
Specifications:
Diameter: 365mm (14.37")
Thickness (new): 28mm (1.10")
Thickness (min.): 26mm (1.02")
Type: 2-piece floating
Face Pattern: Slotted
Vented / Solid: Directional ventilated
Number of Vanes: 48
Hat Material: 6061-T6 aluminum
Friction Ring Material: CM-250 high carbon alloy cast iron
Rotor Finish: CBN turned
Cross Reference:
OEM Tesla 1027632-00-B
EBC D2142
Centric/StopTech 120.52001
Girodisc A2-273
DBA 42769
